1work prior to drilling machine and the card to conduct a comprehensive inspection, confirmed when they work.
2it is forbidden to wear gloves, girls should be linked in the hat.
3clamping workpiece must be reliable. Application of drilling small, tool holder, or the use of hand drill.
4 the use of automatic cutting, to select the feed rate, adjusting the stroke limiting block. Manual feed, generally in accordance with the gradually pressurizing and gradually reduced pressure principle, so too will use the accident.
5bit wound with a long iron, to stop clearance. Prohibit the use of the wind, by hand, to use a brush or iron removal.
6reaming hole, with round and pin, not excessive force, in order to avoid hand against the cutter.
The 7are not allowed in the rotation of the cutter, flip, entrapment or measurement of workpiece. Hands are not allowed to touch a rotating tool.
8 using the rocker drilling, horizontal arm pivot range no obstacles. Before work, arm must clamp.
The 9arm and the work table are not allowed to store objects, to be processed according to the rules of clamping, to prevent the workpiece shift caused significant personal injury accidents and equipment accidents.
At the end of10, the arm down to the lowest position, the spindle box near the column, and are clamped.
摇臂钻床的操作规程：
1．工作前对所用钻床和工卡量进行全面检查，确认无误时方可工作。
2．严禁戴手套操作，女生发辫应挽在帽子内。
3．工件装夹必须牢固可靠。钻小件时，应用工具夹持，不准用手拿着钻。
4．使用自动走刀时，要选好进给速度，调整好行程限位块。手动进刀时，一般按照逐渐增压和逐渐减压原则进行，以免用必过猛造成事故。
5．钻头上绕有长铁屑时，要停车清除。禁止用风吹、用手拉，要用刷子或铁钩清除。
6．精铰深孔时，拔取圆器和销棒，不可用力过猛，以免手撞在刀具上。
7．不准在旋转的刀具下，翻转、卡压或测量工件。手不准触摸旋转的刀具。
8．使用摇臂钻时，横臂回转范围内不准有障碍物。工作前，横臂必须卡紧。
9．横臂和工作台上不准存放物件，被加工件必须按规定卡紧，以防工件移位造成重大人身伤害事故和设备事故。
10．工作结束时，将横臂降到最低位置，主轴箱靠近立柱，并且都要卡紧。
Radial drilling machine operation:
1work prior to drilling machine and the card to conduct a comprehensive inspection, confirmed when they work.
2it is forbidden to wear gloves, girls should be linked in the hat.
3clamping workpiece must be reliable. Application of drilling small, tool holder, or the use of hand drill.
4 the use of automatic cutting, to select the feed rate, adjusting the stroke limiting block. Manual feed, generally in accordance with the gradually pressurizing and gradually reduced pressure principle, so too will use the accident.
5bit wound with a long iron, to stop clearance. Prohibit the use of the wind, by hand, to use a brush or iron removal.
6reaming hole, with round and pin, not excessive force, in order to avoid hand against the cutter.
The 7are not allowed in the rotation of the cutter, flip, entrapment or measurement of workpiece. Hands are not allowed to touch a rotating tool.
8 using the rocker drilling, horizontal arm pivot range no obstacles. Before work, arm must clamp.
The 9arm and the work table are not allowed to store objects, to be processed according to the rules of clamping, to prevent the workpiece shift caused significant personal injury accidents and equipment accidents.
At the end of10, the arm down to the lowest position, the spindle box near the column, and are clamped.